Opening throttle cable for models with ZGULMH00 chassis prefix

We advise you to measure your existing cable before ordering in case you have a non standard set up

 This part is available by special order, request a quote

 883262 MG883262

Exhaust valve for all applications except V50 1 and V50 II where it is used as the inlet valve

Also known as Guzzi ref. 19036182, 19036010 (not inlet for V35 II, Imola, V35C - these use 19036021 only)

 2 in stock

 19036183 GU19036183 19 03 61 83
 1903 6183 1903.6183 19.03.61.83

Inlet or exhaust valve, check parts book or call for exact applications. Exhaust valve on V50 II and V50C

Also known as Guzzi ref. 23036100, 19036150, 19036121, 19036122

 This part is available by special order, request a quote

19036150-z 19036150 GU19036150 19 03 61 50
 1903 6150 1903.6150 19.03.61.50

Rocker cover breather pipes

Also known as Guzzi ref. 23159660, 23159670, 27159660

 2 in stock

 23159671 GU23159671 23 15 96 71
 2315 9671 2315.9671 23.15.96.71

Clutch cable for models with ZGULMH00, ZGULW000,ZGULWC00 or ZGULWJ00 prefix

We advise you to measure your existing cable before ordering in case you have a non standard set up

 1 in stock

 883264 MG883264

Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils

Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit

 This part is due back in stock soon, call 01484 841395 to reserve yours

Sidestand cutout switch

See ELA81319 for rotary switch that was fitted to some models

 This part is available by special order, request a quote

 639542 MG639542

Chrome finish complete indicator supplied with wiring, threaded stem and clamp. Fits front left or rear right

 This part is available by special order, request a quote

 29750663 GU29750663 29 75 06 63
 2975 0663 2975.0663 29.75.06.63

Chrome finish complete indicator supplied with wiring, threaded stem and clamp. Fits front right or rear left

 Sorry, this part is no longer available.

 29750662 GU29750662 29 75 06 62
 2975 0662 2975.0662 29.75.06.62

The innovative Stahlbus bleeder valve allows you to change the brake fluid yourself without assistance. Suitable for models with two bleed nipples per caliper

Linked Guzzi brake systems are notoriously tricky to bleed, this M6 auto bleed nipple can save you hours of tedious squeezing and pumping! This bleed nipple is slightly longer than the standard part so some thread will be left showing even when fully closed.

• Completely sealed by O-ring.
• Hydraulic system remains sealed even during the venting process.
• Reliable non-return function, thus one-man operation.
• System has been bled in minutes.
• Wear of the threads in the caliper is prevented (up and screwing down during the bleeding process).
• For all hydraulic systems such as brakes and clutches stahlbus brake bleed valve just replaces the existing vent screw.
• Tested under extreme conditions by TÜV Rheinland.
  See BRA41652 for bleed valve cover

   More than 5 in stock

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]